Rigid Tube & Wire Thermocouples
(Series TB3)
Ordering Information
Configure this style to request a quote or call for assistance
Part No.:
select options
Start Here
| 1 Series |
2 Calibration |
3 Sheath Diameter |
4 Bend Type |
5 6 Sheath Length |
7 Wire Material |
8 Junction |
9 Termination Style |
10 Special Features |
11 Attached Fitting |
12 13 Isertion Length |
|---|---|---|---|---|---|---|---|---|---|---|
| TB3 |
| 2 | Calibration |
|---|---|
| J | Type J |
| K | Type K |
| T | Type T |
| E | Type E |
| 3 | Sheath Diameter |
|---|---|
| G | 0.118" (3mm) |
| H | 0.125" (3.2mm) (1/8") |
| L | 0.188" (4.8mm) (3/16") (standard) |
| M | 0.236" (6mm) |
| N | 0.250" (6.4mm) (1/4") |
| Sizes for reference only (Standard tolerances apply) | |
| For other diameters consult factory |
| 4 | Bend Type |
|---|---|
| X | 
Straight (standard) |
| Y | 
90 Degree bend |
| Z | 
45 Degree bend |
| 5 6 | Sheath Length |
|---|---|
| ¼-600 |
| 7 | Wire Material |
|---|---|
| A | Fiberglass (800°F) |
| B | Fluoropolymer (400°F) |
| 8 | Junction |
|---|---|
| G | 
Grounded (standard) |
| U | 
Ungrounded |
| W | 
Grounded (Dual Junction) |
| Y | 
Ungrounded Common (Dual) |
| 9 | Termination Style |
|---|---|
| C | 
Standard male plug (400°F) |
| D | 
High temp male plug (660°F) |
| E | 
Max temp male plug (800°F) |
| G | 
Solid pin plug |
| H | 
Standard female jack (400°F) |
| J | 
Miniature plug (400°F) |
| K | 
Miniature jack (400°F) |
| N | 
Standard 3 pin plug w/ ground wire (400°F) |
| P | 
Dual molded male plug (400°F) |
| Z | 
Dual molded female jack (400°F) |
| 10 | Special Features |
|---|---|
| None | |
| 04 | 
Flat tip probe |
| 05 | 
Drill point tip |
| 09 | 
Mating connector |
| 18 | 
Moisture protection boot on connector |
| 24 | 
Fluoropolymer covered probe |
| 25 | 
Free spinning fitting (held on probe by a crimp ring) |
| 26 | 
Connector mounted with tube adapter |
| 29 | 
Silver soldered thermocouple junction |
| 11 | Attached Fitting (optional) |
|---|---|
| None | |
| F01 | 
1/8" npt single thread |
| F02 | 
1/4" npt single thread |
| F03 | 
3/8" npt single thread |
| F04 | 
1/2" npt single thread |
| F05 | 
3/4" npt single thread |
| F06 | 
1/2" npt x 1/2" npt double thread |
| F07 | 
1/2" npt double thread. Spring loaded |
| F08 | 
1/2" npt x 1/2" npt double thread. Spring loaded w/ oil seal |
| F09 | 
1/2" npt x 3/4" npt double thread |
| F10 | 
3/4" npt x 3/4" npt double thread |
| F11 | 
Fixed 7/16" ID single slot bayonet cap assembly |
| F14 | 
1/2" npt x 1" npt double thread |
| F15 | 
1" npt single thread |
| F16 | 
Adjustable 7/16" ID bayonet cap fitting (1/8" OD & 3mm OD) |
| F17 | 
Adjustable 12.5mm ID double slot bayonet cap fitting (1/8" OD & 3mm OD) |
| F18 | 
1/8" npt compression fitting (Brass) |
| F19 | 
1/8" npt compression fitting (Stainless Steel) |
| F20 | 
1/4" npt compression fitting (Brass) |
| F21 | 
1/4" npt compression fitting (Stainless Steel) |
| F28 | 
1" circular mounting flange |
| For other fittings not shown contact factory |
| 12 13 | Insertion Length (when required) |
|---|---|
| None | |
| 1-050 |
