Rigid RTDs with Connector
(Series RB3)
Ordering Information
Configure this style to request a quote or call for assistance
Part No.:
select options
Start Here
1 Series |
2 Element Type |
3 Element Accuracy |
4 Wire Configuration |
5 Sheath Diameter |
6 Sheath Configuration |
7 8 Sheath Length |
9 Termination Style |
10 Special Features |
11 Attached Fitting |
12 13 Insertion Length |
---|---|---|---|---|---|---|---|---|---|---|
RB3 |
2 | Element Type |
---|---|
T | 100 Ω DIN 00385 (thin film) |
U | 500 Ω DIN 00385 (thin film) |
W | 1000 Ω DIN 00385 (thin film) |
X | 120 Ω Nickel DIN 00672 (thin film) |
Y | 100 Ω DIN 003916 (wire wound) |
Z | 500 Ω DIN 003916 (wire wound) |
Q | 10 Ω copper (thin film) |
S | 100 Ω DIN 00385 (wire wound) |
3 | Element Accuracy |
---|---|
A | Class A (0.06%) |
B | Class B (0.12%) |
4 | Wire Configuration |
---|---|
2 | 2-wire |
3 | 3-wire |
4 | 4-wire |
5 | 2-wire (Dual) |
6 | 3-wire (Dual) |
5 | Sheath Diameter |
---|---|
G | 0.118” (3mm) |
H | 0.125” (3.2mm) (1/8") |
J | 0.156” (4mm) |
L | 0.188” (4.8mm) (3/16") |
M | 0.236” (6mm) |
N | 0.250” (6.4mm) (1/4") |
Sizes for reference only (Standard tolerances apply) | |
For other diameters consult factory |
6 | Sheath Configuration |
---|---|
X | Straight (standard) |
Y | 90 Degree bend |
Z | 45 Degree bend |
7 8 | Sheath Length |
---|---|
6-60 |
9 | Termination Style |
---|---|
C | Standard male 2-pin plug (400°F) |
D | Standard male 3-pin plug (400°F) |
F | Standard 2-pin female jack (400°F) |
G | Standard 3-pin female jack (400°F) |
H | Miniature male 2-pin plug (400°F) |
P | Miniature male 3-pin plug (400°F) |
J | Miniature female 2-pin jack (400°F) |
K | Miniature female 3-pin jack (400°F) |
R | Dual molded male 4-pin plug (400°F) (for dual 2 wire) |
T | Dual molded female 4-hole jack (400°F) (for dual 2 wire) |
10 | Special Features |
---|---|
None | |
04 | Flat tip probe |
05 | Drill point tip |
09 | Mating connector |
18 | Moisture protection boot on connector |
24 | Fluoropolymer covered probe |
25 | Free spinning fitting (held on probe by a crimp ring) |
26 | Connector mounted with tube adapter |
11 | Attached Fitting (optional) |
---|---|
None | |
F01 | 1/8" npt single thread |
F02 | 1/4" npt single thread |
F03 | 3/8" npt single thread |
F04 | 1/2" npt single thread |
F05 | 3/4" npt single thread |
F06 | 1/2" npt x 1/2" npt double thread |
F07 | 1/2" npt double thread. Spring loaded |
F08 | 1/2" npt x 1/2" npt double thread. Spring loaded w/ oil seal |
F09 | 1/2" npt x 3/4" npt double thread |
F10 | 3/4" npt x 3/4" npt double thread |
F11 | Fixed 7/16" ID bayonet cap assembly (on MGO probe) (1/8" OD, 3mm OD & 3/16" OD) |
F15 | 1" npt single thread |
F16 | Adjustable 7/16" ID bayonet cap fitting (1/8" OD & 3mm OD) |
F17 | Adjustable 12.5mm ID double slot bayonet cap fitting (1/8" OD & 3mm OD) |
F18 | 1/8" npt compression fitting (Brass) |
F19 | 1/8" npt compression fitting (Stainless Steel) |
F20 | 1/4" npt compression fitting (Brass) |
F21 | 1/4" npt compression fitting (Stainless Steel) |
For other fittings not shown contact factory |
12 13 | Insertion Length (when required) |
---|---|
None | |
0-144 |
- 24 AWG stranded fiberdlass wire inside (700°F) max
- For other configurations contact factory
- Single lead (white) is on the (- pin) for 3-wire RTD connections