Compression Type RTDs
(Series RB2)

RB2 RTD Catalog Page

Ordering Information

Configure this style to request a quote or call for assistance

Part No.:

select options

Start Here

1
Series		 2
Element
Type		 3
Element Accuracy		 4
Wire Config		 5
Sheath Diameter		 6
Sheath
Config		 7 8
Sheath Length		 9
Lead Wire Material		 10
Lead Wire Length		 11
Termination Style		 12
Special Features		 13
Attached
Fitting		 14 15
Insertion
Length
RB2

2 Element Type
T 100 Ω DIN 00385 (thin film)
U 500 Ω DIN 00385 (thin film)
W 1000 Ω DIN 00385 (thin film)
X 120 Ω Nickel DIN 00672 (thin film)
Y 100 Ω DIN 003916 (wire wound)
Z 500 Ω DIN 003916 (wire wound)
Q 10 Ω copper (thin film)
R 200 Ω DIN 00385 (thin film)
S 100 Ω DIN 00385 (wire wound)

3 Element Accuracy
A Class A (0.06%)
B Class B (0.12%)

4 Wire Configuration
2 2-wire
3 3-wire
4 4-wire
5 2-wire (Dual)
6 3-wire (Dual)

5 Sheath Diameter
G 0.118” (3mm)
H 0.125” (3.2mm) (1/8")
J 0.156” (4mm)
L 0.188” (4.8mm) (3/16")
S 0.196” (5mm)
M 0.236” (6mm)
N 0.250” (6.4mm) (1/4")
P 0.314” (8mm) (5/16")
Q 0.375” (9.5mm) (3/8")
  Sizes for reference only (Standard tolerances apply)
  For other diameters consult factory

6 Sheath Configuration
X Straight (standard)
Y 90 Degree bend
Z 45 Degree bend

7 8 Sheath Length
1-60

9 Lead Wire Material
A Fiberglass (800°F)
B Fluoropolymer (400°F)
C Fiberglass with stainless steel braid (800°F) (standard)
D Fluoropolymer with stainless steel braid (400°F)
E Fiberglass with armor cable (800°F) (standard)
F Fluoropolymer with armor cable (400°F)
G Fiberglass with stainless steel braid with armor cable (800°F)
H Fluoropolymer with stainless steel braid with armor cable (400°F)
J Fluoropolymer singles (without white outer jacket) (400°F)

10 Lead Wire Length
6-999
  Over 999" contact factory

11 Termination Style
A 2" stripped leads (bare ends)
B 2" stripped w/ #8 spade lugs
C Standard male 2-pin plug (400°F)
D Standard male 3-pin plug (400°F)
F Standard 2-pin female jack (400°F)
G Standard 3-pin female jack (400°F)
H Miniature male 2-pin plug (400°F)
P Miniature male 3-pin plug (400°F)
J Miniature female 2-pin jack (400°F)
K Miniature female 3-pin jack (400°F)
L 2" stripped leads w/#6 ring terminals
R Dual molded male 4-pin plug (400°F) (for dual 2 wire)
T Dual molded female 4-hole jack (400°F) (for dual 2 wire)
W 2" stripped leads w/ pin terminals
Q 2" stripped leads w/ wire ferrules

X

 Extra long lead wire length (beyond 2” stripped leads)

12 Special Features
  None
02 1.5" long strain relief spring
03 1.5" long heat shrink where wire exits the probe
04 Flat tip probe
05 Drill point tip
06 Epoxy seal
07 Cable Clamp
08 Bx Connector
09 Mating connector
10 Armor cable adaptor
18 Moisture protection boot on connector
21 Fluoropolymer coated armor cable
24 Fluoropolymer covered probe
25 Free spinning fitting (held on probe by a crimp ring)
27 Transition fitting on tube & wire sensor
36 RTD color code White-White-Red (Fluoropolymer)
37 RTD color code Black-White-Red (Fluoropolymer)
38 RTD color code Blue-Orange-White (Fluoropolymer)

13 Attached Fitting (optional)
  None
F01 1/8" npt single thread
F02 1/4" npt single thread
F03 3/8" npt single thread
F04 1/2" npt single thread
F05 3/4" npt single thread
F06 1/2" npt x 1/2" npt double thread
F07 1/2" npt double thread. Spring loaded
F08 1/2" npt x 1/2" npt double thread. Spring loaded w/ oil seal
F09 1/2" npt x 3/4" npt double thread
F10 3/4" npt x 3/4" npt double thread
F16 Adjustable 7/16" ID bayonet cap fitting (1/8" OD & 3mm OD)
F17 Adjustable 12.5mm ID double slot bayonet cap fitting (1/8" OD & 3mm OD)
F18 1/8" npt compression fitting (Brass)
F19 1/8" npt compression fitting (Stainless Steel)
F20 1/4" npt compression fitting (Brass)
F21 1/4" npt compression fitting (Stainless Steel)
F22 1/2" npt compression fitting (Brass)
F23 1/2" npt compression fitting (Stainless Steel)
  For other fittings not shown contact factory

14 15 Insertion Length (when required)
  None
0-50