Mineral Insulated Rigid RTDs w/Connector
(Series RB6)
Ordering Information
Configure this style to request a quote or call for assistance
Part No.:
select options
Start Here
| 1 Series |
2 Element Type |
3 Wire Configuration |
4 Sheath Diameter |
5 6 Sheath Length |
7 Termination Style |
8 Special Features |
9 Attached Fitting |
10 11 Insertion Length |
|---|---|---|---|---|---|---|---|---|
| RB6 |
| 2 | Element Type |
|---|---|
| K | 100 Ω DIN 00385 Class A mineral Insulated element (600°C rated) |
| P | 100 Ω DIN 00385 mineral insulated element (800°C rated) |
| For other elements consult factory |
| 3 | Wire Configuration |
|---|---|
| 2 | 
2-wire |
| 3 | 
3-wire |
| 4 | 
4-wire |
| 5 | 
2-wire (Dual) |
| 6 | 
3-wire (Dual) |
| 4 | Sheath Diameter |
|---|---|
| D | 0.062” (1.6mm) (1/16") |
| H | 0.125” (3.2mm) (1/8") |
| L | 0.188” (4.8mm) (3/16") |
| N | 0.250” (6.4mm) (1/4") |
| Sizes for reference only (Standard tolerances apply) | |
| For other diameters consult factory |
| 5 6 | Sheath Length |
|---|---|
| 6-60 |
| 7 | Termination Style |
|---|---|
| C | 
Standard male 2-pin plug (400°F) |
| D | 
Standard male 3-pin plug (400°F) |
| F | 
Standard 2-pin female jack (400°F) |
| G | 
Standard 3-pin female jack (400°F) |
| H | 
Miniature male 2-pin plug (400°F) |
| P | 
Miniature male 3-pin plug (400°F) |
| J | 
Miniature female 2-pin jack (400°F) |
| K | 
Miniature female 3-pin jack (400°F) |
| R | 
Dual molded male 4-pin plug (400°F) (for dual 2 wire) |
| T | 
Dual molded female 4-hole jack (400°F) (for dual 2 wire) |
| 8 | Special Features |
|---|---|
| None | |
| 04 | 
Flat tip probe |
| 05 | 
Drill point tip |
| 09 | 
Mating connector |
| 18 | 
Moisture protection boot on connector |
| 24 | 
Fluoropolymer covered probe |
| 25 | 
Free spinning fitting (held on probe by a crimp ring) |
| 26 | 
Connector mounted with tube adapter |
| 9 | Attached Fitting (optional) |
|---|---|
| None | |
| F01 | 
1/8" npt single thread |
| F02 | 
1/4" npt single thread |
| F03 | 
3/8" npt single thread |
| F04 | 
1/2" npt single thread |
| F05 | 
3/4" npt single thread |
| F06 | 
1/2" npt x 1/2" npt double thread |
| F07 | 
1/2" npt double thread. Spring loaded |
| F08 | 
1/2" npt x 1/2" npt double thread. Spring loaded w/ oil seal |
| F09 | 
1/2" npt x 3/4" npt double thread |
| F10 | 
3/4" npt x 3/4" npt double thread |
| F11 | 
Fixed 7/16" ID bayonet cap assembly (on MGO probe) (1/8" OD, 3mm OD & 3/16" OD) |
| F15 | 
1" npt single thread |
| F16 | 
Adjustable 7/16" ID bayonet cap fitting (1/8" OD & 3mm OD) |
| F17 | 
Adjustable 12.5mm ID double slot bayonet cap fitting (1/8" OD & 3mm OD) |
| F18 | 
1/8" npt compression fitting (Brass) |
| F19 | 
1/8" npt compression fitting (Stainless Steel) |
| F20 | 
1/4" npt compression fitting (Brass) |
| F21 | 
1/4" npt compression fitting (Stainless Steel) |
| For other fittings not shown contact factory |
| 10 11 | Insertion Length (when required) |
|---|---|
| None | |
| 0-144 |
